How Much Does Sealcoating Cost in Texas?
National cost guides put professional driveway sealcoating at about $1 to $2 per square foot. A two-car driveway of about 400 square feet lands near $400 to $800. One guide’s Austin page lists local work at $1.30 to $1.55 per square foot.
Parking lots cost far less per square foot, at $0.14 to $0.25 in one national guide. These are market numbers as posted in November 2026, not our price list.
What does sealcoating cost per square foot in Texas?
Labor makes up most of the bill. One national guide puts materials at $0.10 to $0.50 per square foot. Labor adds $0.90 to $1.50 per square foot.
Texas numbers run at or above the national ones. Another national guide puts the average job nationwide at $575. Its Austin page puts the average local job at $1,532. Its Texas table runs $940 to $3,950, but it gives no driveway size.
| What the guide measured | Published range | Kind of source |
|---|---|---|
| Driveway, per square foot | $1.00 to $2.00 | National cost guide |
| Austin driveway, per square foot | $1.30 to $1.55 | National guide, Austin page |
| Typical driveway job nationwide | $282 to $868 | National cost guide |
| Typical Austin driveway job | $795 to $2,270 | National guide, Austin page |
| Typical Texas driveway job | $940 to $3,950 | National guide, Texas table |
| Parking lot, per square foot | $0.14 to $0.25 | National guide, parking lot page |
One national guide also prices driveways by size. Its totals include labor.
| Driveway | Square feet | Published total |
|---|---|---|
| One-car, 12 by 24 feet | 288 | $290 to $580 |
| Two-car, 20 by 20 feet | 400 | $400 to $800 |
| Two-car, 24 by 24 feet | 576 | $580 to $1,200 |
| Three-car, 24 by 36 feet | 864 | $860 to $1,700 |
| Circle drive, 50 feet across | 1,650 | $1,700 to $3,300 |
Prep work and the number of coats move a job within these ranges. Our page on sealcoating for driveways and parking lots lays out each step of the job.
What does it cost to sealcoat a parking lot?
The $0.14 to $0.25 per square foot figure comes from one national guide’s parking lot page. Another guide says most lots take up 300 to 350 square feet per car. Simple math on those two figures gives about $40 to $90 per space.
| Lot size | About how many spaces | Math at $0.14 to $0.25 per square foot |
|---|---|---|
| 10,000 square feet | 30 | $1,400 to $2,500 |
| 20,000 square feet | 60 | $2,800 to $5,000 |
| 40,000 square feet | 120 | $5,600 to $10,000 |
Sealer covers the old paint, so the lines go back on after the last coat. The guide with the per-car figure lists striping at $4 to $5 per standard stall. It lists accessible stalls at $25 to $40 each. Plan for restriping the lot along with the sealer.
Potholes and failed patches need fixes before a lot gets sealed. Our parking lot paving and repair page covers that side of the work.
What drives the price of sealcoating?
Size sets the starting number. These factors move it from there:
- Minimum fees. Many contractors set a minimum charge, so a short driveway pays more per square foot. One guide puts service fees at $100 to $200 and says that fee sometimes works as the minimum.
- Prep work. On our jobs, the paving gets a thorough cleaning, and each crack is filled by hand. One guide lists power washing at $0.27 to $0.39 per square foot when it is billed on its own.
- Number of coats. We often recommend two coats. One guide says a second coat costs less than a fresh job, because the prep is already done.
- Sealer type. An Austin cost page lists basic emulsion at $0.10 to $0.14 per square foot for the sealer itself. Latex acrylic runs $0.22 to $0.32, and fill-and-seal runs $0.40 to $0.60. The page says emulsion breaks down faster under Austin heat and sun.
- Coal tar rules. Coal tar is the lowest-priced sealer in one national guide, at $0.06 to $0.10 per square foot. Austin banned it in 2006 to keep its pollutants out of local creeks and lakes. Federal scientists later found those pollutants down 58 percent in the lower part of Lady Bird Lake. A national asphalt engineering institute also advises against coal tar sealers.
- Slope and access. One guide says flat driveways are easier to seal than steep or hard-to-reach ones. That matters on sloped Hill Country lots.
- Repairs. Potholes and wide cracks get fixed before the sealer goes on. That work is its own line on a quote.
How often should you sealcoat in Central Texas?
In Central Texas sun, plan on a fresh coat about every two to three years. Let the surface tell you the exact year. A national asphalt engineering institute says to seal when old asphalt turns dry and brittle. It also says to seal when small surface cracks or loose stone show up.
A state asphalt paving association suggests a fresh coat every two to five years for driveways. Consumer guides say very hot places need it more often, some as often as every other year. Austin fits that hot profile.
NOAA keeps climate normals for Austin’s Camp Mabry station. Its 1991 to 2020 normals show about 123 days a year at 90 degrees or hotter. About 29 of those days reach 100 degrees.
Weather also sets the day. One national guide puts the sealing window at 50 to 95 degrees in dry weather. Another says to have no rain in the forecast for 24 hours after.
In July and August, Austin’s normal highs run near 97 and 98 degrees. Morning hours suit a summer job. Even January’s normal high sits in the low 60s, inside that window on dry days. May is the wettest month in those normals, with October next.
When does asphalt need repairs before sealcoating?
Sealer goes on as a thin coat over the surface. It protects sound asphalt, but it cannot rebuild a failing base. These signs mean repairs come first:
- Potholes or holes that go below the surface
- Long, wide cracks
- Web-like cracking over a soft or sunken spot
- Crumbling edges or loose chunks of asphalt
- Low spots where water sits after rain
Those spots need asphalt repair before any sealer goes down. When damage covers most of the surface, a new layer or a full replacement may be the better spend.
The price gap is wide. One national guide puts small crack and hole repairs at $100 to $400. The same guide puts a full replacement at $4 to $15 per square foot. A fresh coat at the right time costs far less than starting over.
How do you get a written quote for sealcoating?
Published ranges give you a starting point, and your own pavement sets the real price. We look at the job and put the quote in writing.
We sealcoat driveways and parking lots across Leander and the Austin area. See how our sealcoating work is done, or call or text (512) 369-2450 for a free quote.