Asphalt driveways, parking lots and sealcoating around Leander, TXAsphalt paving and sealcoating in Leander
Pavement Solutions
Asphalt milling with a skid steer cold planer in front of a house
Our Services

Asphalt Milling in Leander, TX

Asphalt Milling · Leander, TX

The worn top layer comes off before new asphalt

Asphalt milling grinds the worn top layer off a driveway or parking lot. It clears away cracked, rough asphalt so the new layer goes down on an even surface. Taking the old top off also keeps the new surface level with your garage slab and curbs. Milling comes before the new layer on an asphalt overlay job.

We mill with a planer attachment on a skid steer, sized for driveways and small to mid-size parking lots. Pavement Solutions is an asphalt paving contractor serving Leander and the Austin area. Call or text (512) 369-2450, and we put a free quote in writing after we look at the job.

What We Handle

  • Skid steer planer milling for driveways and small to mid-size lots
  • The worn top layer milled off before an asphalt overlay
  • Cracked, rough asphalt ground down to an even surface
  • Raised spots and lifted edges ground down level
  • Failed asphalt milled out to a clean edge before a patch
  • Keyed edges where new asphalt meets a garage slab or curb
  • A cut depth set so the new layer finishes at the right height
  • The milled surface swept and blown clean before new asphalt

Request an Asphalt Milling Quote

Tell us about the driveway or parking lot and where it is. We look at the job and put a free quote in writing.

How Asphalt Milling Works on a Driveway or Lot

A planer is a spinning drum fitted with hard cutting teeth. Mounted on a skid steer, it grinds the top of the asphalt into small pieces. The cut leaves a rough, grooved surface that is ready for new asphalt.

We set the depth of the cut for each job. A shallow pass takes off a worn, cracked top, and a deeper cut takes out asphalt that has failed. Either way, the goal is an even surface at the right height for the new layer.

Loose millings and dust come off next, because new asphalt bonds best to a clean surface. Before a fresh layer, we air and sweep the surface clean.

Why Mill Before Paving Over Old Asphalt?

Every layer of asphalt adds height. Pave over an old driveway without milling, and it can end up higher than the garage slab. Milling first takes the old surface down, so the new layer finishes at the right height.

Height also decides where rainwater goes. A driveway built up too high at the garage can send runoff toward the door. On a lot with curbs, water has to reach the gutter line. Milling helps set the grade and slope that carry water off the pavement.

The cracked, worn top comes off too. Federal highway guidance warns that wide cracks in old pavement can reflect up through a thin new layer. Milling also evens out ruts, so the new asphalt goes down at an even thickness. On an overlay job, we look at the pavement first, then mill the top layer to grind down cracks.

Asphalt Grinding at Edges and Failed Spots Around Leander

Edges need a clean cut. Where new asphalt meets a garage slab or a curb, we mill a keyed edge. That square cut lets the new asphalt end at full thickness. A thin, feathered edge tends to crack and break away.

Asphalt grinding also takes down raised spots. A lifted edge or a hump in a lot can catch a tire or trip someone. We grind it down so the surface sits even again. If a root or shifting soil lifted it, the cause may still be there.

Failed asphalt comes out the same way. We mill the broken area to a clean, square edge, which gives an asphalt patch firm sides. Leander sits at the center of our service area, and we mill driveways and lots across the Austin area.

Skid steer planer attachment grinding an asphalt surface beside a lawn Freshly milled keyed edge along a concrete curb and gutter

Ready to get started?

Call or text for a written quote. We work about 60 miles around Leander across Central Texas.

(512) 369-2450
How We Work

How a Job With Pavement Solutions Runs

From the first call or text to the finished work, here is how it goes.

1

Call or text

Call or text (512) 369-2450, or send the form. Tell us what needs work and where the property is.

2

We look at the job

We measure the area and check the surface that is there now. We also look at how water drains across it.

3

Your written quote

We put a free quote in writing. Once you say go, we set a work date with you.

4

Grading and prep

We grade the ground and prepare the base for new paving. On worn asphalt, we mill or patch the bad areas first.

5

Paving and the finish

We pave with hot mix asphalt or lay the chip seal, then compact the surface. Sealcoating or striping comes last when the job calls for it.

FAQ

Asphalt Milling Questions, Answered

Common questions about asphalt milling around Leander and the Austin area. If yours is not here, call or text and ask.

Call (512) 369-2450

Is asphalt milling the same as asphalt grinding?
Yes. Both names mean cutting the top layer off old asphalt with a planer. TxDOT's highway specifications call the same work planing. Whatever the name, the worn top comes off and a rough, even surface is left.
What is the difference between asphalt milling and an overlay?
Milling takes the old top layer off. An overlay puts a fresh layer of asphalt over the existing pavement. The two often go together, with milling first and paving second.
Will milling fix a driveway with deep cracks?
Milling takes off the top layer only. Deep cracks or a failed base under the asphalt need more than a new top. When the damage is severe, a full replacement can be the more cost-effective choice. That decision is part of asphalt restoration, and we look at your pavement before we recommend a fix.
What happens to the asphalt that comes off?
It comes off as millings, small pieces of old asphalt. Federal highway research calls this material reclaimed asphalt pavement. By weight, it is 93 to 97 percent stone and sand, and it can go back into new road work. Ask about the millings when we look at your job.
Is a skid steer planer big enough for a parking lot?
Yes, for small to mid-size lots. Our skid steer planer is sized for driveways and for lots in that range. Milling often goes with parking lot paving and repair, and we quote both after we look at the lot.
How much does asphalt milling cost?
The size of the area sets the starting point. The depth of the cut matters, and so do the edges cut at a garage slab or curb. When an overlay or a patch follows, the quote covers the whole job. Call or text (512) 369-2450 for a free quote in writing.
More From Pavement Solutions

Work That Pairs With Asphalt Milling

Parking lot striping with fresh yellow stall lines on new asphalt

Parking Lot Striping

We stripe parking lots across Leander and the Austin area, new lots and faded ones alike. Stall lines, arrows, fire lanes and accessible stalls are laid out to fit your lot.

Learn More
New asphalt driveway curving past a brick mailbox to a brick ranch home

Asphalt Driveways

We install new asphalt driveways and replace old, damaged ones with fresh hot mix asphalt. Every new driveway starts with grading so water flows away from the base.

Learn More
Parking lot paving at a roadside commercial lot with a skid steer and a paver hopper of hot asphalt

Parking Lot Paving

New asphalt parking lots and parking lot repair for businesses across Leander and the Austin area. Each lot is laid out for the flow of traffic and graded so rain runs off.

Learn More
Why Choose Pavement Solutions

Asphalt Paving and Sealcoating Around Leander

Grading before paving

Before any paving work begins, we level and grade the surface so water flows away from it. That goes for driveways with hills and curves too.

Cracks filled by hand

Before we sealcoat, we clean the pavement and fill each crack by hand. We often recommend two coats of sealant.

A free quote in writing

We look at the job before we price it. Then the quote comes to you in writing.

Google Reviews

Rated 4.7 on Google Around Leander

Real reviews from real jobs, 23 reviews on Google.

Read All Reviews

Pavement Solutions did a wonderful job in asphalting our gravel driveway. Professional, courteous service at a reasonable price. We highly recommend them.

Diann Fox7 months ago · Google review

Pavement Solutions has been responsive and professional both times they have completed projects for me. I love the work they’ve done. Saving their number!! Highly recommend!!

Stacy Smith9 months ago · Google review

We had it chip sealed and put chip seal around our barn for mud control and it looks fantastic and is very well done. The entire process was done so well. They are honest, hardworking, polite, great price and do great work. Someone you can trust.

Guides and Resources

Asphalt Milling Guides

Request a Quote

Get In Touch With Pavement Solutions

Tell us about the job with the form, or call or text (512) 369-2450. We get back to you and set a time to look at it.

Request a Quote

Tell us about the driveway or parking lot and where it is. We look at the job and put a free quote in writing.

Call (512) 369-2450